- (tim) [buildpkg.sh.in] Make the names consistent.

[openssh.git] / ssh_config.5

diff --git a/ssh_config.5 b/ssh_config.5
index 50df0d432df3d12ebd3d0de94fd5a3ede7dde3a8..5c94ffc9cdb5fce69a2351dc01af0526f407796f 100644 (file)
--- a/ssh_config.5
+++ b/ssh_config.5
@@ -34,7 +34,7 @@
 .\" (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 .\" THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 .\"
-.\" $OpenBSD: ssh_config.5,v 1.69 2005/12/08 21:37:50 jmc Exp $
+.\" $OpenBSD: ssh_config.5,v 1.76 2006/01/20 11:21:45 jmc Exp $
 .Dd September 25, 1999
 .Dt SSH_CONFIG 5
 .Os
@@ -285,7 +285,7 @@ will continue without connecting to a master instance.
 X11 and
 .Xr ssh-agent 1
 forwarding is supported over these multiplexed connections, however the
-display and agent fowarded will be the one belonging to the master
+display and agent forwarded will be the one belonging to the master
 connection i.e. it is not possible to forward multiple displays or agents.
 .Pp
 Two additional options allow for opportunistic multiplexing: try to use a
@@ -318,7 +318,7 @@ used for opportunistic connection sharing include
 all three of these escape sequences.
 This ensures that shared connections are uniquely identified.
 .It Cm DynamicForward
-Specifies that a TCP/IP port on the local machine be forwarded
+Specifies that a TCP port on the local machine be forwarded
 over the secure channel, and the application
 protocol is then used to determine where to connect to from the
 remote machine.
@@ -530,7 +530,7 @@ The argument to this keyword must be
 .Dq yes
 or
 .Dq no .
-This option is intented for situations where
+This option is intended for situations where
 .Nm ssh-agent
 offers many different identities.
 The default is
@@ -565,7 +565,7 @@ This directive is ignored unless
 .Cm PermitLocalCommand
 has been enabled.
 .It Cm LocalForward
-Specifies that a TCP/IP port on the local machine be forwarded over
+Specifies that a TCP port on the local machine be forwarded over
 the secure channel to the specified host and port from the remote machine.
 The first argument must be
 .Sm off
@@ -718,8 +718,23 @@ or
 The default is
 .Dq yes .
 This option applies to protocol version 2 only.
+.It Cm RekeyLimit
+Specifies the maximum amount of data that may be transmitted before the
+session key is renegotiated.
+The argument is the number of bytes, with an optional suffix of
+.Sq K ,
+.Sq M ,
+or
+.Sq G
+to indicate Kilobytes, Megabytes, or Gigabytes, respectively.
+The default is between
+.Dq 1G
+and
+.Dq 4G ,
+depending on the cipher.
+This option applies to protocol version 2 only.
 .It Cm RemoteForward
-Specifies that a TCP/IP port on the remote machine be forwarded over
+Specifies that a TCP port on the remote machine be forwarded over
 the secure channel to the specified host and port from the local machine.
 The first argument must be
 .Sm off
@@ -797,7 +812,7 @@ across multiple
 directives.
 The default is not to send any environment variables.
 .It Cm ServerAliveCountMax
-Sets the number of server alive messages (see above) which may be
+Sets the number of server alive messages (see below) which may be
 sent without
 .Nm ssh
 receiving any messages back from the server.
@@ -819,7 +834,7 @@ server depend on knowing when a connection has become inactive.
 The default value is 3.
 If, for example,
 .Cm ServerAliveInterval
-(above) is set to 15, and
+(see below) is set to 15, and
 .Cm ServerAliveCountMax
 is left at the default, if the server becomes unresponsive ssh
 will disconnect after approximately 45 seconds.
@@ -891,23 +906,6 @@ This is important in scripts, and many users want it too.
 .Pp
 To disable TCP keepalive messages, the value should be set to
 .Dq no .
-.It Cm UsePrivilegedPort
-Specifies whether to use a privileged port for outgoing connections.
-The argument must be
-.Dq yes
-or
-.Dq no .
-The default is
-.Dq no .
-If set to
-.Dq yes
-.Nm ssh
-must be setuid root.
-Note that this option must be set to
-.Dq yes
-for
-.Cm RhostsRSAAuthentication
-with older servers.
 .It Cm Tunnel
 Request starting
 .Xr tun 4
@@ -927,6 +925,23 @@ Force a specified
 .Xr tun 4
 device on the client.
 Without this option, the next available device will be used.
+.It Cm UsePrivilegedPort
+Specifies whether to use a privileged port for outgoing connections.
+The argument must be
+.Dq yes
+or
+.Dq no .
+The default is
+.Dq no .
+If set to
+.Dq yes
+.Nm ssh
+must be setuid root.
+Note that this option must be set to
+.Dq yes
+for
+.Cm RhostsRSAAuthentication
+with older servers.
 .It Cm User
 Specifies the user to log in as.
 This can be useful when a different user name is used on different machines.