.\" (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
.\" THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
.\"
-.\" $OpenBSD: sshd_config.5,v 1.37 2004/12/23 23:11:00 djm Exp $
+.\" $OpenBSD: sshd_config.5,v 1.43 2005/05/23 23:32:46 djm Exp $
.Dd September 25, 1999
.Dt SSHD_CONFIG 5
.Os
.Dq aes128-ctr ,
.Dq aes192-ctr ,
.Dq aes256-ctr ,
+.Dq arcfour128 ,
+.Dq arcfour256 ,
.Dq arcfour ,
.Dq blowfish-cbc ,
and
.Dq cast128-cbc .
The default is
.Bd -literal
- ``aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour,
- aes192-cbc,aes256-cbc,aes128-ctr,aes192-ctr,aes256-ctr''
+ ``aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,
+ arcfour256,arcfour,aes192-cbc,aes256-cbc,aes128-ctr,
+ aes192-ctr,aes256-ctr''
.Ed
-.It Cm ClientAliveInterval
-Sets a timeout interval in seconds after which if no data has been received
-from the client,
-.Nm sshd
-will send a message through the encrypted
-channel to request a response from the client.
-The default
-is 0, indicating that these messages will not be sent to the client.
-This option applies to protocol version 2 only.
.It Cm ClientAliveCountMax
Sets the number of client alive messages (see above) which may be
sent without
.Cm ClientAliveCountMax
is left at the default, unresponsive ssh clients
will be disconnected after approximately 45 seconds.
+.It Cm ClientAliveInterval
+Sets a timeout interval in seconds after which if no data has been received
+from the client,
+.Nm sshd
+will send a message through the encrypted
+channel to request a response from the client.
+The default
+is 0, indicating that these messages will not be sent to the client.
+This option applies to protocol version 2 only.
.It Cm Compression
Specifies whether compression is allowed.
The argument must be
.Cm GatewayPorts
can be used to specify that
.Nm sshd
-should bind remote port forwardings to the wildcard address,
-thus allowing remote hosts to connect to forwarded ports.
-The argument must be
+should allow remote port forwardings to bind to non-loopback addresses, thus
+allowing other hosts to connect.
+The argument may be
+.Dq no
+to force remote port forwardings to be available to the local host only,
.Dq yes
-or
-.Dq no .
+to force remote port forwardings to bind to the wildcard address, or
+.Dq clientspecified
+to allow the client to select the address to which the forwarding is bound.
The default is
.Dq no .
.It Cm GSSAPIAuthentication
Specifies whether
.Nm sshd
should ignore the user's
-.Pa $HOME/.ssh/known_hosts
+.Pa ~/.ssh/known_hosts
during
.Cm RhostsRSAAuthentication
or
The default is
.Dq no .
.It Cm PermitRootLogin
-Specifies whether root can login using
+Specifies whether root can log in using
.Xr ssh 1 .
The argument must be
.Dq yes ,
.Pp
If this option is set to
.Dq without-password
-password authentication is disabled for root. Note that other authentication
-methods (e.g., keyboard-interactive/PAM) may still allow root to login using
-a password.
+password authentication is disabled for root.
.Pp
If this option is set to
.Dq forced-commands-only
.Pp
If this option is set to
.Dq no
-root is not allowed to login.
+root is not allowed to log in.
.It Cm PermitUserEnvironment
Specifies whether
.Pa ~/.ssh/environment
.It Cm UseDNS
Specifies whether
.Nm sshd
-should lookup the remote host name and check that
+should look up the remote host name and check that
the resolved host name for the remote IP address maps back to the
very same IP address.
The default is